FOMAPAN 200 Creative
BLACK-AND-WHITE NEGATIVE FILM
FOMAPAN 200 Creative is a panchromatically sensitized, black-and-white negative film designed for taking photographs. The film meets high requirements for low
granularity, high resolving power and high contour sharpness. FOMAPAN 200 Creative has a nominal speed rating of ISO 200/24°, but due to its wide exposure
latitude the film gives good results even when being overexposed by 1 EV (exposure value) (as ISO 100/21°) or underexposed by 2 EV (as ISO 800/30°) without
any change in processing, i.e. without lengthening the development time or increasing the temperature of the developer used. To make prints or enlargements,
Fomaspeed- and Fomatone-type enlarging papers are recommended; however, all sorts of black-and-white enlargement papers can be used
ISO 200/24°, 24° CSN
|Lengthening of exposure
|Correction of aperture number
Total darkness or infrared light;
FOMAPAN 200 Creative can be processed in all common negative developers. Recommended development times are shown in the table below (the development times are
related to development in a spiral developing tank - agitation or turning over continuously during the first 30 seconds, then during the first 10 seconds in every
minute). In this way, medium-contrast negatives can be obtained.
When the development time has elapsed, the film is recommended to be shortly rinsed in distilled water or dipped in a 2 % acetic acid solution for 10 seconds.
|Fomadon R09 (1+40)
||8 - 9
|Kentmere Powder film developer (1+1)
||5 - 6
||5 - 6
|Ilford ID 11 stock / Kodak D76
||5 - 6
|Tetenal Emofin Liquid
||4 - 5
At a temperature ranging from 18 to 25°C for 10 minutes in any common type of an acid fixing bath, or for at least 3 minutes in Fomafix rapid fixer.
The film should be washed in running water: for 30 minutes and 15 minutes the temperature of water being below 15°C and over 15°C respectively. It is
recommended to finish the processing with the film being rinsed in distilled water, or dipped in a wetting agent solution.
Unexposed films should be stored in the original packaging in a cool, dry place (temperature ranging from 5 to 20°C, relative humidity from 50 to 60 %), out of
reach of harmful vapours, gases and ionizing radiations. Films stored in a refrigerator and a freezer should be acclimatized to room temperature for approx. 2
and approx. 6 hours respectively. Exposed films should be processed as soon as possible.
FOMAPAN 200 Creative is available in the following sorts:
- 120 rollfilm 60 mm wide, exlusively on a 120 spool
- double-edge perforated 35 mm film in 135-36, 135-24 and 135-12 cartridges for 36, 24 and 12 exposures 24 x 36 mm; bulk lengths of 17, 30.5 and 50 m in a
- sheet film (for large-format cameras) sized: 9 x 12, 10 x 15, 12 x 16.5 13 x 18 and 18 x 24 cm in a box of 50 sheets.
- Other sizes are subject of an agreement with the manufacturer.
110 lines per mm
RMS = 14.0 (Microphen at 20 °C/68°F, developed to G = 0.6. Measured at D = 1.0.
The following bases are used for manufacturing the particular sorts of the film:
- 120 roll film - a bluish polyester base 0.1 mm thick, furnished with a matted color backing which will decolorize during processing. The backing has
anti-halation and anti-curling properties and prevents the incidence of Newton rings during enlarging.
- 35 mm film - a gray or gray-blue cellulose triacetate base 0.135 mm thick,
- sheet film - a clear polyester base 0.175 mm thick furnished with a matted color backing which will decolorize during processing. The backing has anti-halation
and anti-curling properties and prevents the incidence of Newton rings during enlarging.